FAAC Gate Motor Replacement Nationwide

FAAC Gate Motor Replacement: The West Palm Beach Owner’s Guide

A FAAC gate motor replacement in West Palm Beach typically runs between $900 and $2,400 installed, depending on the model series and whether you’re replacing the operator only or the full motor-plus-arm assembly. We stock FAAC-compatible motors and parts on our trucks, and in most cases we can complete the swap the same day we diagnose the failure. The way most homeowners discover they need this part is simple: the gate stops moving, the motor hums but nothing turns, or the keypad opens the gate only sometimes. In West Palm Beach’s heat and salt air, FAAC motors fail gradually, then suddenly, and by the time the gate refuses to open at all, the capacitor, limit switches, or gear train have usually been struggling for months.

Call (728) 203-2413

Key takeaways:

• Installed FAAC motor replacement in West Palm Beach: $900 – $2,400
• Same-day replacement available in most cases
• Written price before any work starts, guaranteed for a full year
• We carry FAAC OEM and quality aftermarket parts on the truck

Which FAAC Models This Applies To

FAAC builds motors for three main applications: swing gates, slide gates, and barrier arms. The 400 Series, 390 Series, and 770 Series cover most residential and light-commercial swing gates we see around West Palm Beach. The 740 and 844 models handle slide gates, and the 620 and 640 work barrier arms at condo and HOA entrances. If you’re not sure which FAAC motor you have, look for the metal rating plate on the side of the operator housing. It lists the model number, voltage, and serial number, and that plate is the single most important piece of information for matching a replacement motor correctly.

One compatibility gotcha worth knowing: FAAC 400 Series operators use a proprietary mounting pattern, and a motor from a 390 will not bolt up to a 400’s gearbox without an adapter plate. We’ve seen owners buy a used motor online and discover this after the gate is already in pieces. When it comes to OEM versus aftermarket, FAAC OEM motors run $100 to $300 more than quality aftermarket equivalents, but the OEM units carry a manufacturer warranty and match the control board’s RPM and torque curve exactly. We install both and tell you the price difference up front so you can choose with the facts on the table.

Signs Your FAAC Gate Motor Replacement Is Failing

• Gate starts moving, then stops halfway. The motor’s thermal overload is tripping because the arm or gear train is binding. In West Palm Beach, rust at the hinge points and salt buildup on the articulating arm joint are common causes, and they force the motor to work harder than it was designed to.
• A low humming sound with no movement. The capacitor that starts the motor has failed. This is one of the most common FAAC failures in Florida because heat shortens capacitor life. We replace the capacitor first, and if the motor still won’t turn, the windings are gone and the motor itself is done.
• Gate drifts open or closed after stopping. The motor’s brake or the gearbox’s holding torque is failing. On FAAC swing operators, a worn brake disc lets the gate creep until it sits partially open, which is also a security problem for the property.
• Clicking from the control board but no motor response. The relay is firing but the motor isn’t receiving consistent voltage. This may be the motor’s internal wiring, or it may be a failed solder joint on the board. We meter both before recommending a replacement.
• Gate works fine in the morning, fails in the afternoon. Heat expansion is causing an internal short or a misaligned limit switch. FAAC limit switches sit inside the operator housing, and on older 400 Series units the plastic cam that triggers them becomes brittle in the Florida sun and cracks.

Lonnie Burke puts it plainly: “Figure out what broke first. Everything else follows from that.” Too many FAAC motors get replaced when the real problem is a $40 capacitor or a misaligned limit switch. We diagnose before we quote, and if the motor isn’t the failure point, we’ll tell you that and fix what actually is.

Replacement Cost & What’s Included

In West Palm Beach, expect to pay $900 to $1,500 for most residential FAAC swing motor replacements, and $1,400 to $2,400 for slide gate and barrier arm models where the gearbox and motor ship as one unit. The spread comes down to three things: which FAAC series you have, whether you choose OEM or aftermarket, and whether the existing arm, bracket, and wiring can be reused. Here’s the cost breakdown you should plan around:

• FAAC motor unit (OEM or aftermarket): $350 – $900
• Labor and installation: $350 – $700
• New arm, bracket, or limit switch if needed: $150 – $500
• Control board reprogramming and safety re-test: included

Every quote we give in West Palm Beach is a written price delivered before any work starts. The number on that sheet is the number you pay, and it includes the motor, the labor, the reprogramming of your existing remotes and keypad, and a full safety re-test of the gate. The work carries the 365-Day Done Right Promise, a written guarantee good for a full year. If the motor fails inside that window, we return and fix it at no charge.

DIY or Call Us?

You can check a few things yourself before calling. Confirm the gate has power, check the breaker, and look at whether photo eyes or safety edges are blocked. If the keypad lights up but the gate doesn’t move, that tells us something useful before we even arrive.

What we don’t recommend is swapping a FAAC motor yourself. These are AC-powered operators wired into your breaker panel, and an incorrect capacitor discharge or a crossed AC connection can cause a serious shock or fire. The motor also has to be phased and travel-limited correctly or the gate will slam through its stops and bend the arm, tear the bracket, or injure someone. A FAAC motor replacement takes our technicians about two hours. If you’re in West Palm Beach and the gate won’t open, call (728) 203-2413 and we’ll get eyes on it.

FAQs