Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateBFT Gate Installation in West Palm Beach: What to Know First
BFT gate installation in West Palm Beach runs from about $1,200 for a single swing arm on an existing gate to $6,500+ for a full double-gate system with operators, safety edges, and loop detectors. We install, wire, and program BFT equipment as an independent service provider, and most jobs take one to two days depending on the gate size and power situation. You get a written price before any work begins, and the number does not move at the door. If you own a BFT operator or are planning a new automated gate and want someone who actually understands BFT equipment, call (728) 203-2413. Lonnie Burke and our crew handle the whole job, from the first measurement to the final test cycle.
Key Takeaways
- We install BFT swing, sliding, and pedestrian gate systems across West Palm Beach, including Northwood Hills, Flamingo Park, and El Cid.
- Every BFT installation includes a written price before work starts and a 365-Day Done Right Promise in writing.
- BFT operators built for European voltage often need specific transformer and wiring attention in Florida homes.
- We stock or can source BFT-specific parts quickly, and we also service LiftMaster, Mighty Mule, Ghost Controls, and DoorKing systems.
Styles & brands we work with
How BFT Products Fail – and How We Fix Them
BFT equipment is well made, but West Palm Beach is a demanding place for any gate motor. Salt air, afternoon storms, and lightning strikes near the coast push these systems harder than the manufacturer’s test bench ever will. Here are the BFT failure patterns we actually see on installation and replacement jobs.
- BFT Aries and Deimos swing operators: capacitor failure from heat and lightning. The Aries line is common on West Palm Beach residential swing gates. The start capacitor sits inside the operator housing, and repeated lightning-induced voltage spikes break down the capacitor’s dielectric. The gate will hum but not move, or it will start and stall halfway. We replace with a capacitor rated for the motor’s exact microfarad value, never a generic close-enough part. Then we check the surge protection on the incoming line.
- BFT Rigel and Phobos sliding operators: limit switch drift. The Rigel series uses magnetic limit switches to tell the gate where to stop. After a season or two in Florida heat, the magnet mounts can loosen and the gate will either slam the end stop or stop a foot short of closed. We reset the limit positions and torque the mounts to spec, then run ten full cycles to confirm the gate lands in the same spot every time.
- BFT Deimos Ultra and Aries Ultra: control board damage from improper power. Many European-spec BFT boards are set at the factory for 230V. If a previous installer wired a 115V line directly to the board without changing the transformer tap, the board works for a while, then fails, often spectacularly. We verify the actual line voltage at the operator before we connect anything. This is basic, and it gets missed constantly.
- BFT Photocell alignment issues from fence and gate settling. West Palm Beach has sandy soil that shifts with the wet and dry seasons. The gate post settles, the photocell beam drifts off target, and the gate refuses to close or intermittently reverses. We check the photocell alignment as a standard part of any BFT installation, even when the customer says the problem is the motor.
- BFT remote receiver desense from mounting location. We see Deimos and Aries operators mounted on steel posts right next to stucco walls with metal lath. The receiver antenna gets pinched between two metal planes and loses range, so the remote only works from ten feet away. We move the antenna or relocate the receiver and the problem goes away. That is a parts positioning fix, not a parts replacement fix.
Our BFT Gate Installation Process
We follow the same process on every BFT job because it keeps the work honest and the price straight. Lonnie Burke came up through welding and metal fabrication at Los Angeles Trade-Technical College, and he runs the crew the same way now: figure out what broke first, then fix exactly that. Everything else follows.
- 1
Phone call and site details. You call (728) 203-2413. A live person answers. We ask about the gate type, the BFT model you have or want, and whether you have photos or measurements.
- 2
On-site inspection and measurements. We come out, check the gate weight, the post condition, the existing wiring, and the power supply. We look for what is already failing before we add new equipment to it.
- 3
Written quote. You get a line-item price for the operator, necessary safety equipment, wiring, and labor. No number moves after this unless you change the scope.
- 4
Installation day. We mount the BFT operator, run the power and control wiring, install safety edges and photocells where required, and program the travel limits, speed, and obstacle detection.
- 5
Testing and walkthrough. We cycle the gate repeatedly, test the auto-reverse force by hand, and show you how the manual release works. You get a rundown of the remote programming and basic troubleshooting.
- 6
Guarantee and cleanup. Every BFT installation carries our written 365-Day Done Right Promise. If something is not right within a year, we come back and fix it at no charge. We leave the site clean and take the old equipment and packaging with us.
See the difference
Before
After
Before
After
Before
AfterWhat BFT Gate Installation Costs in West Palm Beach
Prices vary by gate size, operator model, and whether we are adding automation to an existing gate or building a complete new gate and operator package. Here are the ranges we typically quote in West Palm Beach.
| Job | Typical Price |
|---|---|
| Single swing gate with one BFT Aries or Deimos arm | $1,200 – $2,200 |
| Double swing gate with two BFT operators, sync wiring, and safety edges | $3,000 – $4,800 |
| Sliding gate with BFT Rigel or Phobos operator and rack | $2,400 – $4,200 |
| Pedestrian gate with BFT operator and intercom-ready control board | $1,500 – $2,800 |
| Full new gate fabrication plus BFT automation (driveway, including posts) | $5,500 – $9,000 |
What moves the price: gate weight and material (wrought iron runs heavier than aluminum), distance from the electrical panel to the gate, whether we need to trench under a driveway or sidewalk, and whether you want battery backup for hurricane season. We quote it all in writing before we start. Call (728) 203-2413 for a free estimate on your specific gate.
Why West Palm Beach Homeowners Call Carver Gate Repair West Palm Beach for BFT Work
We are not a general handyman service that occasionally touches a gate. Gates and motor systems are all we do, and BFT is one of nine brands we work on regularly. That matters when the operator on your gate is a BFT Deimos with a European transformer tap and a control board that does not tolerate sloppy wiring. We also service LiftMaster, Mighty Mule, Ghost Controls, and DoorKing, so if your property has a mix of operators across different gates, one call covers all of it.
Every technician who arrives at your property is background-checked and uniformed. You know who you are letting through the gate. Every job gets a written price before work starts, and every repair carries a written guarantee good for a full year. If the repair fails inside that year, the second visit is free. No charge, no argument. Our phones are staffed by a live person 24 hours a day, seven days a week, including holidays. You will not get a voicemail box when you call in the middle of the night with a gate stuck open.
We have been working to The Garrison Standard since 2008, and the standard has not changed: written prices, clean work, and a guarantee we actually stand behind. Lonnie Burke has spent years serving West Palm Beach, including regular work in the Northwood Hills neighborhood, where the mix of older ornamental iron and newer automated systems keeps diagnostics honest. That is where he learned to figure out what broke first before picking up a tool.
Frequently Asked Questions
No, not if the installation is done correctly. BFT warranties cover manufacturing defects, not installation workmanship. As an independent BFT service provider, we install to the manufacturer’s specifications: correct line voltage, proper torque on all mechanical connections, and compliant safety equipment like photocells and edges. We document the installation so you have a record if a warranty claim ever comes up. Call (728) 203-2413 and we will walk you through what your specific BFT model needs.
Most single-operator BFT installations happen within three to five business days of your written quote. Full gate fabrications take longer because the gate has to be built. If you have an existing gate that we are adding BFT automation to, and the electrical is already in place, we can often schedule within the week. Call (728) 203-2413 for current scheduling.
We use genuine BFT parts whenever they are available and practical. For some older boards or motors where the OEM part has been discontinued, we source proven aftermarket replacements that match the electrical specs exactly. We will tell you which we are quoting and why before you pay for anything. The choice is always yours, and it is in writing.
Not necessarily. Slow operation is often a voltage problem at the operator, not a failing motor. We test the line voltage under load before recommending any parts. If you have a long wire run from the panel to the gate, the voltage can drop enough to make the operator sluggish. That is a wiring fix, not a motor replacement. Call (728) 203-2413 for an exact diagnosis.
Yes, and we recommend them on every gate that does not already have them. Florida building code and basic safety both call for entrapment protection on automated gates. We install resistive safety edges, photocell pairs, and test the operator’s auto-reverse force so the gate stops and reverses when it meets resistance. The work is covered by our full-year written guarantee. Call (728) 203-2413 for a free estimate.
Get a Written Price for Your BFT Gate Installation
If your BFT operator is failing or you are ready to automate a gate on your West Palm Beach property, call (728) 203-2413. You will speak to a live person, not a voicemail box. We will schedule an inspection, give you a written price before any work starts, and stand behind the installation with our 365-Day Done Right Promise. The estimate is free, and the price you are quoted is the price you pay.
Written by Lonnie Burke, Owner, Carver Gate Repair West Palm Beach at Carver Gate Repair West Palm Beach, serving West Palm Beach and nearby areas.