FAAC Gate Installation Nationwide

FAAC Gate Installation in West Palm Beach: What to Know First

We install and service FAAC gate operators for homes across West Palm Beach, and we do it as an independent provider, not a manufacturer shop. Most FAAC installations take one full day on site, sometimes two when concrete work or new conduit runs are involved. You’ll get a written price before any work starts, and the number doesn’t move after we’ve opened the gate. If you’re reading this, you probably own a FAAC system that never got installed right or has started failing in ways that seem random. That’s what we handle. Call (728) 203-2413 and you’ll get a live person, 24/7.

Call (728) 203-2413

How FAAC Products Fail – and How We Fix Them

FAAC builds solid operators. The 400, 750, and 844 series show up most often in West Palm Beach driveways, and each has its own way of failing. Here’s what we see on installs and reinstalls across the city:

• FAAC 400 series: capacitor failure that looks like motor death. The 400 is a workhorse on lighter swing gates, but the start capacitor ages quickly in Florida heat. When it goes, the gate grinds, stalls, or trips the board. Plenty of homeowners get quoted a new motor when a $40 capacitor fixes it. That’s the first thing Lonnie Burke checks before anything gets replaced. Figure out what broke first. Everything else follows from that.
• FAAC 750 series: limit switch drift on long driveways. The 750 is built for heavy residential swing gates, but its limit switches drift over time, especially when the gate sees daily sun expansion and afternoon rain cooling. The gate stops six inches short or over-travels and binds. We reset and recalibrate the limits during installation, then verify them under load, not just on the bench.
• FAAC 844 series: water intrusion through the wiring entry. The 844 is a compact sliding-gate operator, and in West Palm Beach the real enemy is the knockout plug. If the installer didn’t seal the conduit entry properly, humidity and rain get in, the board corrodes, and the gate fails intermittently. We seal every entry point with outdoor-rated fittings and check the drain path before we ever mount the unit.
• FAAC hydraulic operators: low oil from the factory is more common than owners think. Some FAAC hydraulic swing operators ship with fluid at the minimum mark. In South Florida heat, that thin margin causes sluggish movement or overheating. We check and top off hydraulic fluid as part of every FAAC installation, and we log the level so you know what we found.
• FAAC E145 control board: photocell conflicts that other installers miss. The E145 board pairs with FAAC’s safety photocells, but wiring them to the wrong input causes the gate to behave like a haunted machine, opening halfway and reversing. This is especially common when FAAC motors get paired with aftermarket safety edges. We land every wire where the board expects it and test every safety device before calling the job done.

Our FAAC Gate Installation Process

Every FAAC job in West Palm Beach follows the same sequence. No surprises, no shortcuts.

1. 1
   The site walk. We check the gate’s weight, hinge condition, travel path, and the condition of any existing wiring. On a new install, we look at where the operator will sit, how power reaches it, and whether the ground drains. If the gate is heavy and the hinges are shot, we tell you before quoting the operator.
2. 2
   Parts decision. We use FAAC OEM parts when the warranty matters and the right aftermarket part when it doesn’t. We’ll show you both options, explain the trade-off in plain terms, and let you decide. Either way, the written price comes before the work.
3. 3
   The install. Mount, wire, seal, and set limits. Every conduit entry gets sealed against rain. Every safety device gets wired to the correct input. No zip ties where stainless hardware belongs.
4. 4
   Load testing. We run the gate through full open and close cycles with the gate loaded, not just free-swinging. This catches limit drift, motor strain, and board errors that bench tests miss.
5. 5
   Safety verification. Photocells, safety edges, and force settings get tested. If the gate can’t reverse safely on obstruction, we don’t walk away from it.
6. 6
   The guarantee. Every FAAC install carries our 365-Day Done Right Promise in writing. If the repair fails inside the year, the second visit is free. No charge, no argument.

What FAAC Gate Installation Costs in West Palm Beach

Here are real numbers for common FAAC jobs in the West Palm Beach area, based on what we’ve quoted on properties from Northwood Hills to the acreage west of 95.

• FAAC operator replacement, labor included: $1,400 – $2,600 depending on the operator model and whether we’re reusing existing wiring.
• Full FAAC swing gate install with operator, arms, and controls: $3,200 – $6,800, with gate weight and concrete work moving the number.
• FAAC sliding gate install, new track and operator: $3,800 – $7,500. Rusted track replacement or a new concrete pad pushes toward the high end.
• FAAC control board replacement, part and labor: $380 – $750, including reprogramming and limit reset.
• FAAC safety edge or photocell replacement: $220 – $480 per device, installed and tested.

What moves the price most is gate condition before we start. A heavy iron gate with bad hinges costs more to do right than a light aluminum one. Underground conduit that needs replacing is another common add. The quote you get is the price you pay, written down before the first tool comes off the truck. Call (728) 203-2413 for a free estimate on your FAAC system.

Why West Palm Beach Homeowners Call Carver Gate Repair West Palm Beach for FAAC Work

We don’t ask you to trust us, we give you the specifics. Every FAAC install from our crew carries a written one-year guarantee, not a verbal promise. The technician who arrives is background-checked and in uniform, and the phone gets answered by a live person at 3 a.m. the same way it does at noon. We work on FAAC every week, but we also carry the expertise for LiftMaster, Mighty Mule, Ghost Controls, and DoorKing, which means if your FAAC board dies and the best fix is switching the control system while keeping your existing gate, we can lay out that option honestly instead of forcing a brand replacement. That’s the real reason people stay with us after the first job.

FAQs