Ghost Controls Hinge & Roller Replacement Nationwide

Ghost Controls Hinge & Roller Replacement: The West Palm Beach Owner’s Guide

We stock and install Ghost Controls-compatible hinge and roller replacements throughout West Palm Beach, with most jobs running $185 to $420 installed depending on gate weight and how many pivot points need attention. That price includes the parts, the labor, and a written guarantee good for a full year. Most owners discover the problem when the gate starts dragging at the latch side, or when it takes noticeably more effort to swing open than it did six months ago.

Call (728) 203-2413

A hinge or roller failure on a Ghost Controls swing gate rarely announces itself. It creeps in: a slight sag at the free end, a scrape mark on the concrete, a gate that stops mid-travel because the motor is now fighting friction it wasn’t designed for. By the time you see visible wear, the geometry of the whole gate has already changed, and that puts strain on the Ghost Controls operator itself. Fix the hinge now, or replace the operator next year. Lonnie Burke puts it plainly: “Figure out what broke first. Everything else follows from that.”

Which Ghost Controls Models This Applies To

Ghost Controls builds swing gate operators under the R-series and A-series designations, plus the controls and arms that drive them. The hinges and rollers themselves are rarely Ghost Controls-branded parts. Ghost Controls manufactures the motor, the arm, and the control board. The gate hardware, hinges, rollers, and pivot brackets, comes from the gate fabricator or a third-party hardware supplier. That matters because an owner searching for “Ghost Controls hinge replacement” often assumes the part carries a Ghost Controls part number. It usually doesn’t.

What you actually need is a hinge or roller matched to your gate’s weight, construction, and post setup, not to the operator model. We carry OEM-grade and quality aftermarket replacements in the common South Florida sizes: 2-inch and 3-inch barrel hinges, adjustable weld-on hinges for ornamental iron, and steel-bearing rollers sized for track systems on sliding Ghost Controls configurations. The compatibility gotcha we see in West Palm Beach all the time: an owner replaces a worn hinge with a lighter-duty part because it looked the same at the hardware store, and the gate sags again within eight months. Gate weight, not appearance, drives the spec.

Signs Your Ghost Controls Hinge & Roller Replacement Is Failing

• Gate sags at the latch end. The top hinge wears into an oval over time, allowing the free end of the gate to drop. You’ll see the latch no longer aligns with the receiver, and the gate scrapes a growing arc into the driveway.
• Scrape marks on concrete or pavers. When a roller fails or a hinge elongates, the gate’s clearance shrinks. The scrape mark is the symptom; the worn pivot is the cause. Ignoring it turns a $200 hinge replacement into a welded gate frame repair.
• Operator strain or false reversals. A Ghost Controls motor that trips its obstruction sensor mid-cycle, when nothing is in the way, is often fighting a binding hinge. The board reads the added resistance as an obstacle and reverses. Homeowners replace the board when they should be checking the hardware.
• Audible grinding or squealing at the pivot. Salt air in West Palm Beach accelerates rust on unsealed hinge pins. Once the pin starts grinding inside the barrel, lubrication buys weeks, not months. The fix is replacement, not grease.
• Visible rust bloom or cracked weld at the hinge bracket. Rust on ornamental iron in a coastal climate is not cosmetic. It works into the weld’s heat-affected zone and creates stress cracks. We replace hinges and the affected bracket section before the gate drops entirely.

Replacement Cost & What’s Included

For West Palm Beach homes, plan on $185 to $320 to replace one to two hinges or gate rollers on a typical single-swing Ghost Controls gate. A heavier double-swing gate with adjustable weld-on hinges, or a sliding gate that needs both rollers and a new guide track section, typically lands between $300 and $420. The range reflects gate weight, the number of pivot points being replaced, and whether we’re match-welding new brackets or working with bolt-on replacements.

Every quote is written before we touch the gate. That is The Garrison Standard, and it means the number you approve is the number you pay. No add-ons at the door. The work includes removal of the old hardware, installation of the replacement, adjustment so the gate sits square and true, and a full travel test of the Ghost Controls operator to confirm the motor is no longer fighting the gate. And every repair carries our written 365-Day Done Right Promise: if the repair fails inside a year, we return and make it right at no charge.

DIY or Call Us?

You can diagnose the problem yourself with eyes and hands. Push the gate gently at the latch end and watch for movement at the hinge barrel. If there’s play, the hinge is worn. Run your hand along the bottom track on a sliding gate and feel for flat spots on the rollers. Those are safe checks, and they’ll tell you what you’re dealing with before you spend a dollar.

The replacement itself? On an ornamental iron gate in West Palm Beach, this is where we earn our keep. A single-swing Ghost Controls gate can weigh 300 to 600 pounds. If you unbolt a hinge without supporting the gate correctly, the gate drops and it doesn’t just damage the driveway. It can crush a foot or hand, and it can bend the gate frame beyond repair. We use a gate jack, we match the hinge spec to the actual gate weight, and we align the replacement before we weld or tighten anything. If you’re not set up for that, call (728) 203-2413 and we’ll handle it.

FAQs